咨询电话:13699145010
Products产品中心

固体绝缘材料绝缘电阻测试仪

简要描述:本仪器既可测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围Z宽,准确度Z高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数

  • 产品型号:
  • 厂商性质:生产厂家
  • 更新时间:2022-07-15
  • 访  问  量:689

详细介绍

固体绝缘材料绝缘电阻测试仪

符合标准:
GB/T 1410-2006《 固体绝缘材料体积电阻率和表面电阻率试验方法》
ASTM D257-99《绝缘材料的直流电阻或电导试验方法》
GB/T 10581-2006 《绝缘材料在高温下电阻和电阻率的试验方法》
GB/T 1692-2008 《硫化橡胶 绝缘电阻率的测定》
GB/T 2439-2001《硫化橡胶或热塑性橡胶 导电性能和耗散性能电阻率的测定》
GB/T 12703.4-2010 《纺织品 静电性能的评定 第4部分:电阻率》
GB/T 10064-2006_《测定固体绝缘材料绝缘电阻的试验方法》
GB/T 22042-2008《服装 防静电性能 表面电阻率试验方法》
EN 1149-1-1995 《防护服 静电性能 第1部分表面电阻检验方法和要求》
GB/T 1410-2006《固体绝缘材料体积电阻率和表面电阻率试验方法》(与标准IEC93-1980等效)
FZ/T 64013-2008 《静电植绒毛绒》
SJ/10694-2006《电子产品制造与应用系统防静电检测通用规范》6.1 
一、概述
    本仪器既可测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围zui宽,准确度zui高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数方便.     适用于橡胶、塑料、薄膜、地毯、织物及粉体、液体、及固体和膏体形状的各种绝缘材料体积和表面电阻值的测定。
二、主要特点
电阻测量范围宽 1×104Ω ~1×1018Ω
电流测量范围为 2×10-4A ~1×10-16A
体积小、重量轻、准确度高
电阻、电流双显示
性能好稳定、读数方便
所有测试电压(10V/50V/100/250/500/1000V) 测试时电阻结果直读,免去老式高阻计在不同测试电压下或不同量程时要乘以系数等使用不便的麻烦,使测量超高电阻就如用万用表测量普通电阻样简便。既能测超高电阻又能测微电流
三、技术指标
1、电阻测量范围: 0.01×104Ω ~1×1018Ω。
2、电流测量范围为: 2×10-4A~1×10-16A
3、显 示 方 式:数字液晶显示
4、内置测试电压: 10V 、50V、100V、250、500、1000V
5、基本准确度:1% (*注)
6、使用环境: 温度:0℃~40℃,相对湿度<80%
7、机内测试电压: 10V/50V/100/250/500/1000V 任意切换
8、供电形式: AC 220V,50HZ,功耗约5W
9、仪器尺寸: 285mm× 245mm× 120 mm
10、质量: 约5KG
四、工作原理
    根据欧姆定律,被测电阻Rx等于施加电压V除以通过的电流I。传统的高阻计的工作原理是测量电压V固定,通过测量流过取样电阻的电流I来得到电阻值。从欧姆定律可以看出,由于电流I是与电阻成反比,而不是成正比,所以电阻的显示值是非线性的,即电阻无穷大时,电流为零,即表头的零位处是∞,其附近的刻度非常密,分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时,其电压V也会有些变化,所以普通的高阻计是精度差、分辨率低。
    本仪器是同时测出电阻两端的电压V和流过电阻的电流I,通过内部的大规模集成电路完成电压除以电流的计算,然后把所得到的结果经过A/D转换后以数字显示出电阻值,即便是电阻两端的电压V和流过电阻的电流I是同时变化,其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流I的变而变,所以,即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大,其测量精度很高(),从理论上讲其误差可以做到零,而实际误差可以做到千分之几或万分之几。
典型应用
1、测量绝缘材料电阻(率)
2、测量防静电材料的电阻及电阻率
3、测量计算机房用活动地板的系统电阻值
4、测量防静电鞋、导电鞋的电阻值
5、光电二极管暗电流测量
6、物理,光学和材料研究
标准配置:
1、测试仪器:1台
2、电源线:1条
3、测量线:3根(屏蔽线、测试接线、接地线)
4、使用说明书:1份
备注:
本仪器配不同的测量电极(夹具)可以测量不同材料(固体、粉体或液体)的体积电阻率和表面电阻率或电导率,完全符合国家标准GB1410-2006固体电工绝缘材料绝缘电阻、体积电阻系数和表面电阻试验方法,ASTM D257 绝缘材料的直流电阻或电导试验方法 等标准要求。
注意事项:
仪器使用前请仔细阅读以下内容,否则将造成仪器损坏或电击情况。
1. ★检查仪器后面板电压量程是否置于10V档,电流电阻量程是否置于104档。
2. ★接通电源调零,(注意此时主机不得与屏蔽箱线路连接)在“Rx"两端开路的情况下,调零使电流表的显示为0000。然后关机。
3. ★将待测试样平铺在不保护电极正中央,然后用保护电极压住样品,再插入被保护电极(不保护电极、保护电极、被保护电极应同轴且确认电极之间无短路)。
4. ★测体积电阻时测试按钮拨到Rv边,测表面电阻时测试按钮拨到Rs边,
5. ★接好测试线,将测试线将主机与屏蔽箱连接好。量程置于104档,打开主机后面板电源开关按钮。从仪器后面板调电压按钮到所要求的测量电压。
(比如:GBT 1692-2008 硫化橡胶 绝缘电阻率的测定 标准中注明要求在500V电压进行测定,那么电压就要升到500V)
6. ★电流电阻量程按钮从低档位逐渐拨高档,每拨一次停留1-2秒观察显示数字,当被测电阻大于仪器测量量程时,电阻表显示“1",此时应继续将仪器拨到量程更高的位置。
测量仪器有显示值时应停下,在1min的电化时间后测量电阻,当前的数字乘以档次即是被测电阻。
7. ★测试完毕先将量程拨至(104)档,然后将测量电压拨至10V档,zui后将测试按钮拨到中央位置后关闭电源。然后进行下一次测试。
8. ★应在“Rx"两端开路时调零,一般一次调零后在测试过程中不需再调零。
9. ★禁止将“RX"两端短路,以免微电流放大器受大电流冲击。
10. ★不得在测试过程中不要随意改动测量电压。
11. ★测量时从低次档逐渐拨往高次档。
12. ★接通电源后,手指不能触及高压线的金属部分。
13. ★不得测试过程中不能触摸微电流测试端。
14. ★在测量高阻时,应采用屏蔽盒将被测物体屏蔽。
15. ★严禁在试测过程随意改变电压量程及在通电过程中打开主机。
16. ★严禁电流电阻量程未在104档及电压在10V档,更换试样。

Meet the standard:

GB/T 1410-2006《 固体绝缘材料体积电阻率和表面电阻率试验方法》

GB/T 1410-2006 "solid insulating material volume resistivity and surface resistivity test method"

ASTM D257-99《绝缘材料的直流电阻或电导试验方法》

DC resistance or conductance of insulating materials test method "ASTM D257-99"

GB/T 10581-2006 《绝缘材料在高温下电阻和电阻率的试验方法》

Test method GB/T 10581-2006 "insulation resistance at high temperature and resistivity"

GB/T 1692-2008 《硫化橡胶 绝缘电阻率的测定》

Determination of 1692-2008 vulcanized rubber insulation resistivity of "GB/T"

GB/T 2439-2001《硫化橡胶或热塑性橡胶 导电性能和耗散性能电阻率的测定》

GB/T 2439-2001 "rubber vulcanized or thermoplastic conductive properties and dissipative properties determination of resistivity"

GB/T 12703.4-2010 《纺织品 静电性能的评定 第4部分:电阻率》

GB/T 12703.4-2010 "textile xerographic performance evaluation of fourth parts: the resistivity"

GB/T 10064-2006_《测定固体绝缘材料绝缘电阻的试验方法》

GB/T 10064-2006_ "determination of solid insulation resistance of insulation materials test method"

GB/T 22042-2008《服装 防静电性能 表面电阻率试验方法》

GB/T 22042-2008 "garment test methods for the prevention of electrostatic properties of surface resistivity"

EN 1149-1-1995 《防护服 静电性能 第1部分表面电阻检验方法和要求》

EN 1149-1-1995 "protective clothing electrostatic properties of first part surface resistance test methods and requirements"

GB/T 1410-2006《固体绝缘材料体积电阻率和表面电阻率试验方法》(与标准IEC93-1980等效)

GB/T 1410-2006 "solid insulating material volume resistivity and surface resistivity test method" (international standard IEC93-1980 equivalent)

FZ/T 64013-2008 《静电植绒毛绒》

FZ/T 64013-2008 "electrostatic flocking Plush"

SJ/10694-2006《电子产品制造与应用系统防静电检测通用规范》6.1

SJ/10694-2006 "electronic product manufacturing and application of anti electrostatic detection system general specification" 6.1

一、概述

One, overview

本仪器既可测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围zui宽,准确度zui高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数方便. 适用于橡胶、塑料、薄膜、地毯、织物及粉体、液体、及固体和膏体形状的各种绝缘材料体积和表面电阻值的测定。

This instrument can measure high resistance, but also can measure current. Use of large scale integrated circuit American company In, the instrument has the advantages of small volume, light weight and high accuracy. Digital LCD display resistance value and the current. Range from 1 × 104 Ω to 1 × 1018 Ω, is currently the most wide measuring range, accuracy the highest high resistance measuring instrument. Current measuring range is 2 × 10-4 ~ 1 × 10-16A. The built-in test voltage 10V/50V/100V/250V/500V/1000V adjustable. The instrument has high precision, good stability, shows a rapid, convenient reading. Suitable for rubber, plastics, film, carpets, fabrics and powder, liquid, and solid and pasty shape insulating materials by volume and surface resistance value.

二、主要特点

Two, the main features

电阻测量范围宽 1×104Ω ~1×1018Ω

Resistance measurement range of 1 × 104 to 1 × 1018 Ω

电流测量范围为 2×10-4A ~1×10-16A

Current measuring range is 2 × 10-4A ~ 1 × 10-16A

体积小、重量轻、准确度高

Small volume, light weight, high accuracy

电阻、电流双显示

Resistance, current double display

性能好稳定、读数方便

Good performance is stable, easy reading

所有测试电压(10V/50V/100/250/500/1000V) 测试时电阻结果直读,免去老式高阻计在不同测试电压下或不同量程时要乘以系数等使用不便的麻烦,使测量超高电阻就如用万用表测量普通电阻样简便。既能测超高电阻又能测微电流

All voltage test (10V/50V/100/250/500/1000V) resistance results test reading, from old high resistance meter in different test voltage or different range should be multiplied by the coefficient of inconvenience and trouble, ultra high resistance as measured with a multimeter common resistance is measured. Not only can measure high resistance and micro current

三、技术指标

Three, technical indicators

1、电阻测量范围: 0.01×104Ω ~1×1018Ω。

1, resistance measurement range: 0.01 × 104 ~ 1 × 1018 Ω.

2、电流测量范围为: 2×10-4A~1×10-16A

2, the current measurement range: 2 × 10-4A ~ 1 × 10-16A

3、显 示 方 式:数字液晶显示

3, the display mode: Digital LCD display

4、内置测试电压: 10V 、50V、100V、250、500、1000V

4, the built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V

5、基本准确度:1% (*注)

5, basic accuracy: 1% (note)

6、使用环境: 温度:0℃~40℃,相对湿度<80%

6, the use of the environment: temperature: 0 ℃ ~ 40 ℃, relative humidity <80%

7、机内测试电压: 10V/50V/100/250/500/1000V 任意切换

7, the built-in test voltage: 10V/50V/100/250/500/1000V arbitrary switching

8、供电形式: AC 220V,50HZ,功耗约5W

8, the power supply form: AC 220V, 50HZ, power consumption is about 5W

9、仪器尺寸: 285mm× 245mm× 120 mm

9, the instrument size: 285mm x 245mm x 120 mm

10、质量: 约5KG

10, quality: about 5KG

四、工作原理

Four, work principle

根据欧姆定律,被测电阻Rx等于施加电压V除以通过的电流I。传统的高阻计的工作原理是测量电压V固定,通过测量流过取样电阻的电流I来得到电阻值。从欧姆定律可以看出,由于电流I是与电阻成反比,而不是成正比,所以电阻的显示值是非线性的,即电阻无穷大时,电流为零,即表头的零位处是∞,其附近的刻度非常密,分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时,其电压V也会有些变化,所以普通的高阻计是精度差、分辨率低。

According to Ohm's law, the measured resistance Rx is equal to the applied voltage divided by current V by I. The working principle of high resistance meter is the traditional measure voltage V fixed, by measuring the current flows through the sampling resistor I to get the resistance value. From Ohm's law can be seen, the current I is inversely proportional to the resistance, not proportional, so is nonlinear resistive display value, namely the infinite resistance, current is zero, i.e. zero at the header is ∞, graduated in the vicinity of the very tight, very low resolution. The scale is nonlinear. Because the resistance measurement is different, its voltage V there will be some changes, so the high resistance of ordinary meter is poor accuracy, low resolution.

本仪器是同时测出电阻两端的电压V和流过电阻的电流I,通过内部的大规模集成电路完成电压除以电流的计算,然后把所得到的结果经过A/D转换后以数字显示出电阻值,即便是电阻两端的电压V和流过电阻的电流I是同时变化,其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流I的变而变,所以,即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大,其测量精度很高(),从理论上讲其误差可以做到零,而实际误差可以做到千分之几或万分之几。

This instrument is current and voltage V and flow resistance at the same time measuring resistor I, the large scale integrated circuit internal to complete the calculation of voltage divided by current, and then the obtained results after A/D conversion to digital display resistance value, even if is current and voltage of V and flow resistance at both ends of the I is changed at the same time, the displayed value resistance do not like ordinary high resistance meter for V measured voltage or current change of I variable and variable, so, even if the measurement of voltage, resistance, power supply voltage is measured and the change had little effect on the results, the measuring accuracy is very high (patent), theoretically the error can be do zero, while the actual error can be done a few thousandths or very few.

典型应用

Typical applications

1、测量绝缘材料电阻(率)

Insulation resistance 1, measurement (rate)

2、测量防静电材料的电阻及电阻率

2, the measurement of anti resistance and resistivity electrostatic materials

3、测量计算机房用活动地板的系统电阻值

3, the measurement used in computer room floor system resistance value

4、测量防静电鞋、导电鞋的电阻值

Resistance of 4, measurement of anti-static shoes, conductive shoes value

5、光电二极管暗电流测量

5, photoelectric diode dark current measurement

6、物理,光学和材料研究

6, physical, optical and material research

标准配置:

Standard configuration:

1、测试仪器:1台

1, test equipment: 1 sets

2、电源线:1条

2, power line: 1

3、测量线:3根(屏蔽线、测试接线、接地线)

3, the measuring line: 3 (shielding line, test line, ground wire)

4、使用说明书:1份

4, use instructions: 1

备注:

Remarks.

本仪器配不同的测量电极(夹具)可以测量不同材料(固体、粉体或液体)的体积电阻率和表面电阻率或电导率,完全符合国家标准GB1410-2006固体电工绝缘材料绝缘电阻、体积电阻系数和表面电阻试验方法,ASTM D257 绝缘材料的直流电阻或电导试验方法 等标准要求。

This instrument measuring electrode with different (fixture) can measure different materials (solid, powder or liquid) of the volume resistivity and surface resistivity or conductivity, fully meet the national standard GB1410 - 2006 solid electrical insulation resistance, volume resistivity and surface resistance test method of material, ASTM D257 DC resistance or conductance of insulating materials test method standard.

注意事项:

Matters needing attention:

仪器使用前请仔细阅读以下内容,否则将造成仪器损坏或电击情况。

The instrument before use, please read the following carefully, otherwise it will cause equipment damage or shock condition.

1. ★检查仪器后面板电压量程是否置于10V档,电流电阻量程是否置于104档。

1. Check the instrument panel after voltage range is placed in the 10V file, current resistance range is placed 104.

2. ★接通电源调零,(注意此时主机不得与屏蔽箱线路连接)在“Rx"两端开路的情况下,调零使电流表

2 ★ power zero, (note that the host may not be connected with the shielding box line) in the "Rx" both ends open circuit case, zero current meter

The electrical properties of China aerotime and common instrument of insulating material

ZWN万能材料试验机

ZWN universal material testing machine

ZJC-10KV-200KV电压击穿试验仪

ZJC-10KV-200KV voltage breakdown tester

ZST-121体积表面电阻率测定仪

Determination of ZST-121 volume and surface resistivity instrument

ZTS-121碳素材料电阻率测试仪

ZTS-121 carbon material resistivity tester

ZST-122电线电缆导体半导体材料电阻率测试仪

Instrument cable conductor semiconductor material resistivity ZST-122

M-200橡胶塑料滑动摩擦试验机(国标,非国标,可定制)

M-200 rubber plastic sliding friction testing machine (GB, non standard, can be customized)

ZJD-A介电常数介质损耗测试仪(可测试固体液体)

ZJD-A dielectric loss tester (testing of solid liquid)

ZJD-B学校介电常数介质损耗测试仪

ZJD-B school special dielectric loss tester

ZJD-C高频介电常数介质损耗测试仪

ZJD-C high frequency dielectric loss tester

ZJD-50HZ-100HZ工频介电常数介质损耗测试仪

ZJD-50HZ-100HZ frequency dielectric loss tester

ZDH-20KV绝缘材料耐电弧性能试验仪/高电压小电流测试仪

Arc resistance tester / high voltage low current tester ZDH-20KV insulating material

ZWK-300A液显热变形维卡软化点温度测定仪

ZWK-300A liquid heat deformation temperature of VEKA softening point tester

ZWK-300B计算机控制热变形维卡温度试验机

VEKA ZWK-300B computer control thermal deformation temperature testing machine

ZWK-500计算机控制热变形维卡温度试验机

VEKA ZWK-500 computer control thermal deformation temperature testing machine

ZQYH-96塑料球压痕硬度计

ZQYH-96 plastic ball indentation hardness tester

ZRT-400Z熔体流动速率测定仪/熔融指数仪

ZRT-400Z melt flow rate meter / melt index apparatus

ZMD-A计算机控制马丁耐热试验仪

ZMD-A computer control Martin heat resistance tester

☆中航时代燃烧性能仪器

☆ China aerotime combustion performance instrument

ZRS-3水平垂直燃烧试验仪

ZRS-3 horizontal and vertical burning tester

ZDG-1000单根电线电缆垂直燃烧试验仪

ZDG-1000 vertical burning test instrument of single wire and cable

ZLD-600V漏电起痕试验仪

ZLD-600V tracking test apparatus

ZLD-6000V高压漏电起痕试验仪

ZLD-6000V high voltage tracking test apparatus

ZKR-A建材可燃性试验炉

ZKR-A building materials flammability test furnace

ZBR-B建材不燃性试验炉

ZBR-B building materials not combustion test furnace

ZZR-A汽车内饰材料阻燃性能试验机

Flame retardant properties of automotive interior materials testing machine ZZR-A

ZY-A针焰试验仪

ZY-A needle flame test apparatus

ZR-A灼热丝试验仪

ZR-A glow wire test apparatus

ZDR-C导热系数测定仪

Determination of ZDR-C thermal conductivity coefficient instrument

☆中航时代海绵泡沫检测仪器

☆ China aerotime sponge foam detecting instrument

ZYX-2000海绵泡沫压陷硬度测定仪

ZYX-2000 sponge foam indentation hardness tester

ZLQ-500海绵泡沫落球回弹仪

ZLQ-500 sponge foam ball rebound tester

ZPL-2000海绵泡沫疲劳冲击测定仪

ZPL-2000 sponge foam fatigue impact tester

ZLS-1000海绵拉伸强度试验机

ZLS-1000 sponge tensile strength testing machine

ZYS-200海绵压缩*变形试验机

Compression testing machine ZYS-200 sponge

ZQG-500海绵泡沫切割机

ZQG-500 sponge foam cutting machine

ZMD-A海绵密度测定仪

ZMD-A sponge density measuring instrument

ZYZS-C氧指数测定仪

ZYZS-C oxygen index tester

ZR-B海绵泡沫阻燃性能试验箱

Test box flame retardant sponge foam properties of ZR-B

☆中航时代冲击试验机系类

☆ China aerotime impact testing machine series

ZWD系类低温脆性试验机(单试样、多试样)

ZWD series of brittle - temperature testing machine (single specimen, multiple sample)

ZJZL-A简支梁冲击试验机(指针,数显)

ZJZL-A Charpy impact testing machine (pointer, digital display)

ZXBL-A悬臂梁冲击试验机(指针,数显)

ZXBL-A cantilever beam impact testing machine (pointer, digital display)

ZJX-A简支梁悬臂梁组合冲击试验机(指针,数显)

ZJX-A simply supported cantilever beam combination impact testing machine (pointer, digital display)

ZLC-2000落球冲击试验机

ZLC-2000 falling ball impact test machine

ZLB-30管材落镖冲击试验机

ZLB-30 pipe falling dart impact tester

BCM-03摆锤薄膜冲击试验机

Pendulum impact testing machine of BCM-03 thin films

ZJS-300A金属摆锤冲击试验机

ZJS-300A metal pendulum impact testing machine

ZJS-300B全自动低温冲击试验机

ZJS-300B automatic temperature impact test machine

☆中航时代制样机系类

☆ China aerotime system prototype system

ZWN-A万能制样机

The ZWN-A universal machine

ZQK-A手动缺口制样机

ZQK-A manual gap system prototype

ZQK-B自动缺口制样机

ZQK-B automatic gap system prototype

ZYL-A手动哑铃型制样机

ZYL-A manual dumbbell system prototype

ZQK-B自动哑铃型制样机

ZQK-B automatic dumbbell system prototype

冲片机(气动、液压)

Punching machine (pneumatic, hydraulic)

☆中航时代环境试验箱系类

☆ China aerotime environmental test box series

ZJB-C高低温交变试验箱

ZJB-C alternating high and low temperature test box

ZQH-C人工气候箱

ZQH-C artificial climate box

ZLH-A老化试验箱

ZLH-A aging test box

ZWS-02高低温试验箱

ZWS-02 high low temperature test box

ZYZS-C氧指数测定仪

ZYZS-C oxygen index tester

☆售后服务

☆ after sale service

一、安装调试:协助试验机的安装,负责试验机的运输、调试。

A, installation debugging: assist testing machine installation, transportation, commissioning test machine.

二、验收标准:试验机按订货技术附件进行验收。终验收在买方进行,对用户提供的试样进行试验,并提供测试报告。

Two, acceptance criteria: testing machine for acceptance according to the order of the technical annex. Final acceptance in the buyer, sample provides to the user testing, and provide the test report.

三、培训:安装调试同时,在仪器操作现场一次性免费培训操作人员2-3名,该操作人员应是由需方选派的长期稳定的员工,培训后能够对设备基本原理、软件使用、操作、维护事项理解和应用,使人员能够独立操作设备对样品进行检测、分析,同时能进行基本的维护。

Three, training: installation at the same time, the instrument operation on-site one-time free training 2-3, the operating personnel shall be appointed by the long-term stability of the staff, training to basic principle, software use, operation, maintenance and application of understanding, so that workers can operate independently equipment to detect samples, analysis, at the same time can carry out basic maintenance.

四、软件升级:终生免费提供新版本控制软件。

Four, software upgrade: free lifetime provides new version control software.

五、保修:

Five, the warranty:

1、设备保修两年,终身售后服务,一年内非人为损坏的零部件免费更换,保修期内接到用户邀请后, zui迟响应时间为2小时内,在与用户确认故障后,我公司会在48小时内派工程师到达现场进行免费服务,尽快查清故障所在位置和故障原因,并向用户及时报告故障的原因和排除办法 。

1, equipment warranty of two years, lifetime after sale service, within one year of the non-human damage parts replaced free of charge, the warranty period the user received the invitation, but the response time is 2 hours, with user confirmation after a failure, I will send engineers arrived at the scene for free within 48 hours of service, find out the fault location and the fault reason as soon as possible, and to users timely report failures and troubleshooting.

2、保修期内人为损坏的零部件按采购(加工)价格收费更换。

2, the warranty period of man-made damaged parts procurement according to the price of replacement (processing).

3、保修期外继续为用户提供优质技术服务,在接到用户维修邀请后3天内派工程师到达用户现场进行维修。并享有优惠购买零配件的待遇。

3, the warranty period to continue to provide high-quality technical services for the users, to invite users to repair within 3 days after the arrival of the user site to send engineers to repair. And enjoy the preferential purchase of spare parts.

4、传感器过载及整机电路超压损坏不在保修范围内。

4, the sensor and the circuit overload overpressure damage not covered under warranty.

六、售后管理:

Six, customer service management:

我公司实现计算机化管理,实行客户定期回访制度,定期复查设备的工作情况,定期指导用户对设备进行保养和检测,以便设备正常运转,跟踪客户的设备使用情况,以便及时对设备进行维护。

Our company to realize the computer management, carry out customer regular ephone return visit system, work regular examination equipment, regular ephone guide users to maintain and test the equipment, so that the normal operation of equipment, track customer equipment usage, so that timely equipment for maintenance.


产品咨询

留言框

  • 产品:

  • 您的单位:

  • 您的姓名:

  • 联系电话:

  • 常用邮箱:

  • 省份:

  • 详细地址:

  • 补充说明:

  • 验证码:

    请输入计算结果(填写阿拉伯数字),如:三加四=7
北京中航时代仪器设备有限公司
  • 联系人:石磊
  • 地址:北京市房山区经济技术开发区1号
  • 邮箱:zhsdyq@163.com
  • 传真:86-010-80224846
关注我们

欢迎您关注我们的微信公众号了解更多信息

扫一扫
关注我们
版权所有 © 2022 北京中航时代仪器设备有限公司 All Rights Reserved    备案号:京ICP备14029093号-1    sitemap.xml
管理登陆    技术支持:化工仪器网    
扫一扫访问手机站扫一扫访问手机站
访问手机站