咨询电话:13699145010
Products产品中心

GB/T 22042服装点对点电阻率测试仪

简要描述:本仪器既可测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围Z宽,准确度Z高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数

  • 产品型号:
  • 厂商性质:生产厂家
  • 更新时间:2024-01-30
  • 访  问  量:1162

详细介绍

品牌AIRTIMES/中航时代

符合标准:
GB/T 1410-2006《 固体绝缘材料体积电阻率和表面电阻率试验方法》
ASTM D257-99《绝缘材料的直流电阻或电导试验方法》
GB/T 10581-2006 《绝缘材料在高温下电阻和电阻率的试验方法》
GB/T 1692-2008 《硫化橡胶 绝缘电阻率的测定》
GB/T 2439-2001《硫化橡胶或热塑性橡胶 导电性能和耗散性能电阻率的测定》
GB/T 12703.4-2010 《纺织品 静电性能的评定 第4部分:电阻率》
GB/T 10064-2006_《测定固体绝缘材料绝缘电阻的试验方法》
GB/T 22042-2008《服装 防静电性能 表面电阻率试验方法》
EN 1149-1-1995 《防护服 静电性能 第1部分表面电阻检验方法和要求》
GB/T 1410-2006《固体绝缘材料体积电阻率和表面电阻率试验方法》(与标准IEC93-1980等效)
FZ/T 64013-2008 《静电植绒毛绒》
SJ/10694-2006《电子产品制造与应用系统防静电检测通用规范》6.1 
一、概述
    本仪器既可测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围zui宽,准确度zui高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数方便.     适用于橡胶、塑料、薄膜、地毯、织物及粉体、液体、及固体和膏体形状的各种绝缘材料体积和表面电阻值的测定。
二、主要特点
电阻测量范围宽 1×104Ω ~1×1018Ω
电流测量范围为 2×10-4A ~1×10-16A
体积小、重量轻、准确度高
电阻、电流双显示
性能好稳定、读数方便
所有测试电压(10V/50V/100/250/500/1000V) 测试时电阻结果直读,免去老式高阻计在不同测试电压下或不同量程时要乘以系数等使用不便的麻烦,使测量超高电阻就如用万用表测量普通电阻样简便。既能测超高电阻又能测微电流
三、技术指标
1、电阻测量范围: 0.01×104Ω ~1×1018Ω。
2、电流测量范围为: 2×10-4A~1×10-16A
3、显 示 方 式:数字液晶显示
4、内置测试电压: 10V 、50V、100V、250、500、1000V
5、基本准确度:1% (*注)
6、使用环境: 温度:0℃~40℃,相对湿度<80%
7、机内测试电压: 10V/50V/100/250/500/1000V 任意切换
8、供电形式: AC 220V,50HZ,功耗约5W
9、仪器尺寸: 285mm× 245mm× 120 mm
10、质量: 约5KG
四、工作原理
    根据欧姆定律,被测电阻Rx等于施加电压V除以通过的电流I。传统的高阻计的工作原理是测量电压V固定,通过测量流过取样电阻的电流I来得到电阻值。从欧姆定律可以看出,由于电流I是与电阻成反比,而不是成正比,所以电阻的显示值是非线性的,即电阻无穷大时,电流为零,即表头的零位处是∞,其附近的刻度非常密,分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时,其电压V也会有些变化,所以普通的高阻计是精度差、分辨率低。
    本仪器是同时测出电阻两端的电压V和流过电阻的电流I,通过内部的大规模集成电路完成电压除以电流的计算,然后把所得到的结果经过A/D转换后以数字显示出电阻值,即便是电阻两端的电压V和流过电阻的电流I是同时变化,其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流I的变而变,所以,即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大,其测量精度很高(),从理论上讲其误差可以做到零,而实际误差可以做到千分之几或万分之几。
典型应用
1、测量绝缘材料电阻(率)
2、测量防静电材料的电阻及电阻率
3、测量计算机房用活动地板的系统电阻值
4、测量防静电鞋、导电鞋的电阻值
5、光电二极管暗电流测量
6、物理,光学和材料研究
标准配置:
1、测试仪器:1台
2、电源线:1条
3、测量线:3根(屏蔽线、测试接线、接地线)
4、使用说明书:1份
备注:
本仪器配不同的测量电极(夹具)可以测量不同材料(固体、粉体或液体)的体积电阻率和表面电阻率或电导率,*符合国家标准GB1410-2006固体电工绝缘材料绝缘电阻、体积电阻系数和表面电阻试验方法,ASTM D257 绝缘材料的直流电阻或电导试验方法 等标准要求。
注意事项:
仪器使用前请仔细阅读以下内容,否则将造成仪器损坏或电击情况。
1. ★检查仪器后面板电压量程是否置于10V档,电流电阻量程是否置于104档。
2. ★接通电源调零,(注意此时主机不得与屏蔽箱线路连接)在“Rx"两端开路的情况下,调零使电流表的显示为0000。然后关机。
3. ★将待测试样平铺在不保护电极正中央,然后用保护电极压住样品,再插入被保护电极(不保护电极、保护电极、被保护电极应同轴且确认电极之间无短路)。
4. ★测体积电阻时测试按钮拨到Rv边,测表面电阻时测试按钮拨到Rs边,
5. ★接好测试线,将测试线将主机与屏蔽箱连接好。量程置于104档,打开主机后面板电源开关按钮。从仪器后面板调电压按钮到所要求的测量电压。
(比如:GBT 1692-2008 硫化橡胶 绝缘电阻率的测定 标准中注明要求在500V电压进行测定,那么电压就要升到500V)
6. ★电流电阻量程按钮从低档位逐渐拨高档,每拨一次停留1-2秒观察显示数字,当被测电阻大于仪器测量量程时,电阻表显示“1",此时应继续将仪器拨到量程更高的位置。
测量仪器有显示值时应停下,在1min的电化时间后测量电阻,当前的数字乘以档次即是被测电阻。
7. ★测试完毕先将量程拨至(104)档,然后将测量电压拨至10V档,zui后将测试按钮拨到中央位置后关闭电源。然后进行下一次测试。
8. ★应在“Rx"两端开路时调零,一般一次调零后在测试过程中不需再调零。
9. ★禁止将“RX"两端短路,以免微电流放大器受大电流冲击。
10. ★不得在测试过程中不要随意改动测量电压。
11. ★测量时从低次档逐渐拨往高次档。
12. ★接通电源后,手指不能触及高压线的金属部分。
13. ★不得测试过程中不能触摸微电流测试端。
14. ★在测量高阻时,应采用屏蔽盒将被测物体屏蔽。
15. ★严禁在试测过程随意改变电压量程及在通电过程中打开主机。
16. ★严禁电流电阻量程未在104档及电压在10V档,更换试样。

Meet the standard:

GB/T 1410-2006《 固体绝缘材料体积电阻率和表面电阻率试验方法》

GB/T 1410-2006 "solid insulating material volume resistivity and surface resistivity test method"

ASTM D257-99《绝缘材料的直流电阻或电导试验方法》

DC resistance or conductance of insulating materials test method "ASTM D257-99"

GB/T 10581-2006 《绝缘材料在高温下电阻和电阻率的试验方法》

Test method GB/T 10581-2006 "insulation resistance at high temperature and resistivity"

GB/T 1692-2008 《硫化橡胶 绝缘电阻率的测定》

Determination of 1692-2008 vulcanized rubber insulation resistivity of "GB/T"

GB/T 2439-2001《硫化橡胶或热塑性橡胶 导电性能和耗散性能电阻率的测定》

GB/T 2439-2001 "rubber vulcanized or thermoplastic conductive properties and dissipative properties determination of resistivity"

GB/T 12703.4-2010 《纺织品 静电性能的评定 第4部分:电阻率》

GB/T 12703.4-2010 "textile xerographic performance evaluation of fourth parts: the resistivity"

GB/T 10064-2006_《测定固体绝缘材料绝缘电阻的试验方法》

GB/T 10064-2006_ "determination of solid insulation resistance of insulation materials test method"

GB/T 22042-2008《服装 防静电性能 表面电阻率试验方法》

GB/T 22042-2008 "garment test methods for the prevention of electrostatic properties of surface resistivity"

EN 1149-1-1995 《防护服 静电性能 第1部分表面电阻检验方法和要求》

EN 1149-1-1995 "protective clothing electrostatic properties of first part surface resistance test methods and requirements"

GB/T 1410-2006《固体绝缘材料体积电阻率和表面电阻率试验方法》(与标准IEC93-1980等效)

GB/T 1410-2006 "solid insulating material volume resistivity and surface resistivity test method" (international standard IEC93-1980 equivalent)

FZ/T 64013-2008 《静电植绒毛绒》

FZ/T 64013-2008 "electrostatic flocking Plush"

SJ/10694-2006《电子产品制造与应用系统防静电检测通用规范》6.1

SJ/10694-2006 "electronic product manufacturing and application of anti electrostatic detection system general specification" 6.1

一、概述

One, overview

本仪器既可测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围zui宽,准确度zui高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数方便. 适用于橡胶、塑料、薄膜、地毯、织物及粉体、液体、及固体和膏体形状的各种绝缘材料体积和表面电阻值的测定。

This instrument can measure high resistance, but also can measure current. Use of large scale integrated circuit American company In, the instrument has the advantages of small volume, light weight and high accuracy. Digital LCD display resistance value and the current. Range from 1 × 104 Ω to 1 × 1018 Ω, is currently the most wide measuring range, accuracy the highest high resistance measuring instrument. Current measuring range is 2 × 10-4 ~ 1 × 10-16A. The built-in test voltage 10V/50V/100V/250V/500V/1000V adjustable. The instrument has high precision, good stability, shows a rapid, convenient reading. Suitable for rubber, plastics, film, carpets, fabrics and powder, liquid, and solid and pasty shape insulating materials by volume and surface resistance value.

二、主要特点

Two, the main features

电阻测量范围宽 1×104Ω ~1×1018Ω

Resistance measurement range of 1 × 104 to 1 × 1018 Ω

电流测量范围为 2×10-4A ~1×10-16A

Current measuring range is 2 × 10-4A ~ 1 × 10-16A

体积小、重量轻、准确度高

Small volume, light weight, high accuracy

电阻、电流双显示

Resistance, current double display

性能好稳定、读数方便

Good performance is stable, easy reading

所有测试电压(10V/50V/100/250/500/1000V) 测试时电阻结果直读,免去老式高阻计在不同测试电压下或不同量程时要乘以系数等使用不便的麻烦,使测量超高电阻就如用万用表测量普通电阻样简便。既能测超高电阻又能测微电流

All voltage test (10V/50V/100/250/500/1000V) resistance results test reading, from old high resistance meter in different test voltage or different range should be multiplied by the coefficient of inconvenience and trouble, ultra high resistance as measured with a multimeter common resistance is measured. Not only can measure high resistance and micro current

三、技术指标

Three, technical indicators

1、电阻测量范围: 0.01×104Ω ~1×1018Ω。

1, resistance measurement range: 0.01 × 104 ~ 1 × 1018 Ω.

2、电流测量范围为: 2×10-4A~1×10-16A

2, the current measurement range: 2 × 10-4A ~ 1 × 10-16A

3、显 示 方 式:数字液晶显示

3, the display mode: Digital LCD display

4、内置测试电压: 10V 、50V、100V、250、500、1000V

4, the built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V

5、基本准确度:1% (*注)

5, basic accuracy: 1% (note)

6、使用环境: 温度:0℃~40℃,相对湿度<80%

6, the use of the environment: temperature: 0 ℃ ~ 40 ℃, relative humidity <80%

7、机内测试电压: 10V/50V/100/250/500/1000V 任意切换

7, the built-in test voltage: 10V/50V/100/250/500/1000V arbitrary switching

8、供电形式: AC 220V,50HZ,功耗约5W

8, the power supply form: AC 220V, 50HZ, power consumption is about 5W

9、仪器尺寸: 285mm× 245mm× 120 mm

9, the instrument size: 285mm x 245mm x 120 mm

10、质量: 约5KG

10, quality: about 5KG

四、工作原理

Four, work principle

根据欧姆定律,被测电阻Rx等于施加电压V除以通过的电流I。传统的高阻计的工作原理是测量电压V固定,通过测量流过取样电阻的电流I来得到电阻值。从欧姆定律可以看出,由于电流I是与电阻成反比,而不是成正比,所以电阻的显示值是非线性的,即电阻无穷大时,电流为零,即表头的零位处是∞,其附近的刻度非常密,分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时,其电压V也会有些变化,所以普通的高阻计是精度差、分辨率低。

According to Ohm's law, the measured resistance Rx is equal to the applied voltage divided by current V by I. The working principle of high resistance meter is the traditional measure voltage V fixed, by measuring the current flows through the sampling resistor I to get the resistance value. From Ohm's law can be seen, the current I is inversely proportional to the resistance, not proportional, so is nonlinear resistive display value, namely the infinite resistance, current is zero, i.e. zero at the header is ∞, graduated in the vicinity of the very tight, very low resolution. The scale is nonlinear. Because the resistance measurement is different, its voltage V there will be some changes, so the high resistance of ordinary meter is poor accuracy, low resolution.

本仪器是同时测出电阻两端的电压V和流过电阻的电流I,通过内部的大规模集成电路完成电压除以电流的计算,然后把所得到的结果经过A/D转换后以数字显示出电阻值,即便是电阻两端的电压V和流过电阻的电流I是同时变化,其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流I的变而变,所以,即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大,其测量精度很高(),从理论上讲其误差可以做到零,而实际误差可以做到千分之几或万分之几。

This instrument is current and voltage V and flow resistance at the same time measuring resistor I, the large scale integrated circuit internal to complete the calculation of voltage divided by current, and then the obtained results after A/D conversion to digital display resistance value, even if is current and voltage of V and flow resistance at both ends of the I is changed at the same time, the displayed value resistance do not like ordinary high resistance meter for V measured voltage or current change of I variable and variable, so, even if the measurement of voltage, resistance, power supply voltage is measured and the change had little effect on the results, the measuring accuracy is very high (patent), theoretically the error can be do zero, while the actual error can be done a few thousandths or very few.

典型应用

Typical applications

1、测量绝缘材料电阻(率)

Insulation resistance 1, measurement (rate)

2、测量防静电材料的电阻及电阻率

2, the measurement of anti resistance and resistivity electrostatic materials

3、测量计算机房用活动地板的系统电阻值

3, the measurement used in computer room floor system resistance value

4、测量防静电鞋、导电鞋的电阻值

Resistance of 4, measurement of anti-static shoes, conductive shoes value

5、光电二极管暗电流测量

5, photoelectric diode dark current measurement

6、物理,光学和材料研究

6, physical, optical and material research

标准配置:

Standard configuration:

1、测试仪器:1台

1, test equipment: 1 sets

2、电源线:1条

2, power line: 1

3、测量线:3根(屏蔽线、测试接线、接地线)

3, the measuring line: 3 (shielding line, test line, ground wire)

4、使用说明书:1份

4, use instructions: 1

备注:

Remarks.

本仪器配不同的测量电极(夹具)可以测量不同材料(固体、粉体或液体)的体积电阻率和表面电阻率或电导率,*符合国家标准GB1410-2006固体电工绝缘材料绝缘电阻、体积电阻系数和表面电阻试验方法,ASTM D257 绝缘材料的直流电阻或电导试验方法 等标准要求。

This instrument measuring electrode with different (fixture) can measure different materials (solid, powder or liquid) of the volume resistivity and surface resistivity or conductivity, fully meet the national standard GB1410 - 2006 solid electrical insulation resistance, volume resistivity and surface resistance test method of material, ASTM D257 DC resistance or conductance of insulating materials test method standard.

注意事项:

Matters needing attention:

仪器使用前请仔细阅读以下内容,否则将造成仪器损坏或电击情况。

The instrument before use, please read the following carefully, otherwise it will cause equipment damage or shock condition.

1. ★检查仪器后面板电压量程是否置于10V档,电流电阻量程是否置于104档。

1. Check the instrument panel after voltage range is placed in the 10V file, current resistance range is placed 104.

2. ★接通电源调零,(注意此时主机不得与屏蔽箱线路连接)在“Rx"两端开路的情况下,调零使电流表

2 ★ power zero, (note that the host may not be connected with the shielding box line) in the "Rx" both ends open circuit case, zero current meter

产品咨询

留言框

  • 产品:

  • 您的单位:

  • 您的姓名:

  • 联系电话:

  • 常用邮箱:

  • 省份:

  • 详细地址:

  • 补充说明:

  • 验证码:

    请输入计算结果(填写阿拉伯数字),如:三加四=7
北京中航时代仪器设备有限公司
  • 联系人:石磊
  • 地址:北京市房山区经济技术开发区1号
  • 邮箱:zhsdyq@163.com
  • 传真:86-010-80224846
关注我们

欢迎您关注我们的微信公众号了解更多信息

扫一扫
关注我们
版权所有 © 2024 北京中航时代仪器设备有限公司 All Rights Reserved    备案号:京ICP备14029093号-1    sitemap.xml
管理登陆    技术支持:化工仪器网